sciencelasas.blogg.se - How to create own os for mikrotik routeros

HOW TO CREATE OWN OS FOR MIKROTIK ROUTEROS UPDATE
HOW TO CREATE OWN OS FOR MIKROTIK ROUTEROS FULL
HOW TO CREATE OWN OS FOR MIKROTIK ROUTEROS PASSWORD

Set networks for ALL users, with strong passwords.

Set networks for ALL services even if they are disabled.

Turn off the unused services (IP services and tool/BTest server).

Improve the default firewall rules, and never disable them.

HOW TO CREATE OWN OS FOR MIKROTIK ROUTEROS PASSWORD

Set a strong password for your own user.

How do i check access through a specific port - ex.

How do i test internet access from console/terminal?.

Check that you have a next hop set with /ip route nexthop print - or read more about next hop. If you set the default route gateway to an interface like ether1, the router will not use this route to lookup next hop, and you will not have access through this route.

Is the default gateway of route 0.0.0.0/0 route set to the IP of the next hop router?.

Have you added a default 0.0.0.0/0 route?.

I have local network access from same local subnet, but no internet access? There is no technical difference as to what private network you use internally, but if you happen to use the exact same /24 network as your technicians use at home or elsewhere, it might become a nuisance for VPNs. See RouterOS 6.41 master-port to bridge changes. If you are unsure what is included in your device, you can check the cpu with /system resource print and check if a switch chip is present with /interface ethernet switch print. Example: ether1-slave-crs-17 (ether1 is a slave port, and is cabled to your CRS switch on the CRS switch port 17). Rename the interfaces, so they represent your chosen setup and where they are connected to. Check your devices setup of master ports with:

HOW TO CREATE OWN OS FOR MIKROTIK ROUTEROS FULL

For devices including a switch chip, you will usually connect all ports to one master port, to gain full wire speed switching. Since most RouterOS devices can perform either as layer 2 or layer 3, you need to choose your setup of switch chip and CPU. If you have several ports cabled on the network, then bridge the ports and add the address on the bridge. address "10.0.1.1/24", no network, and put the IP on the interface that is cabled to the network. If you need the router to be able to route/connect to internal networks, give the router an IP on each network, and it will create a dynamic route in the routing table and be able to connect.

HOW TO CREATE OWN OS FOR MIKROTIK ROUTEROS UPDATE

A MikroTik by default updates it's time use a MikroTik cloud, check Winbox: IP ⇢ Cloud: Update time is enabled. If you wish to setup a NTP/SNTP client to update from your own network, disable the cloud time. You will probably also want to setup the /Firewall, /Wireless and /IP DHCP server.Ī MikroTik has no time/date keeping battery, so it needs to update time+date on each boot. That is all - you are done with the simple setup to get internet access.Update software: System ⇢ Packages: Check for updates./ip firewall nat add chain=srcnat action=masquerade out-interface=ether1.If you need to supply NAT for local IPs:.address: 0.0.0.0/0 - Gateway: IP of next router) (or /ip route add gateway=1.2.3.4) Add a default gateway/route: IP ⇢ Route: Add (+) (Dst.7.9.13.1/24 - no network - choose the connected interface) Add a public IP: IP ⇢ Address list: Add (+) (ex.If you need to setup public IP yourself:.Enable a DHCP client: IP ⇢ DHCP Client: Add (+) ⇢ Interface: ether1.

If your provider are servicing you DHCP:.Change the admin password: System ⇢ Password.Disable unneeded access services: Winbox: IP ⇢ Services (disable all other except Winbox).Factory reset config if needed: Winbox: System ⇢ Reset Configuration (check No Default Configuration to get a completely clean device, otherwise it will use factory default settings).In a virtual CHR environment or with console cable: /setup.Insert cable to your ISP in ether1 and a cable to your own system in ether2. For easy setup, you may:.